These are new M201 delay fuze columns without the threaded fuze subassembly. The once fired delay is pressed out and the new one pressed in, being careful not to press against or damage the primer thus causing accidental firing. Tooling can be made from a wooden dowell with a concave end so it only contacts the rim of the fuze column and not the primer. These fit the M201 subassemblies only.

Out of stock

As the photos above depict, this subassembly consists of the delay fuze column pressed within the threaded subassembly, ready for use.Use the spoon and spring kit from your once fired device to complete the assembly for use. Purchase more M201 delay fuze columns for these above.

Out of stock

As the photos above depict, this subassembly consists of the delay fuze column pressed within the threaded subassembly, ready for use. Use the spoon and spring kit from your once fired device to complete the assembly for use.

Out of stock

These are the loaded brass propellant cartridges used to fire the 40mm smoke grenades and other devices. They are pressed into place within the 40mm aluminum or steel casings and supply the power to propel the insert.

Out of stock

RACER BULLET LOADING DIES

COMPRESS PYROTECHNICS INTO BULLET BASE

MAKE YOUR OWN COLORFUL TRACERS FOR RIFLE OR PISTOL CALIBERS! Our patent pending tool design features a precision machined threaded (7/8 -14) steel compression die with interchangeable non-sparking brass ram and an aluminum bullet die with interchangeable plastic sleeve housing the pre-drilled bullet for compressing the pyrotechnic tracer composition. Simply thread the compression die into any standard single station ammo reloading press, slip the bullet die into ram press, insert appropriate pre-drilled bullet into sleeve, fill with your favorite composition and compress by lowering press handle - simple!! We have designed the set to use inexpensive interchangeable parts to upgrade to a different caliber without purchasing an additional threaded die set!! Example: if you wish to load both 30 caliber and 45, simply order the die set in one caliber and the upgrade kit for the other. Loading dies include threaded die with lock rings, brass ram, bullet die, bullet sleeve for one caliber and complete instructions listing how to easily drill the bullet base cavities for each caliber using FMJ or hard cast bullets and ordinary drill bits obtained at most any hardware store. Upgrade kits include bullet sleeve and brass ram. See diagram A - opposite page.

Call For Availability.

"SILENCER" LOOK BARREL - 17MM - METRIC THREAD FOR BLANK / WILDLIFE CONTROL PISTOLS

Machined from 3 1/2" long solid aluminum and metric threaded to fit the older style 15mm blank pistols with thread-on barrels. Both 15mm & 17mm devices may be used and launched higher becaise of the longer barrel. Its "silencer look" adds character to you pistol as well! Load your own wildlife control cartridges, whistles, bangs, etc. using 9/16" ID X 1/16" wall tubes (roll your own) or flare pellets using our 9/16" pellet pumps for signalling applications.

9/16 " STAR & FLARE PELLET PUMPS - ALUMINUM

Machined aluminum pump for pressing aerial flares, stars and other compositions such as smoke and ignition pellets that can be fired from 15mm blank / wildlife control pistols. Set includes mold sleeve, ram and instructions with color flare formulations. Now you can use your blank pistol for an aerial signaling. The pellets may be used in aerial shells as well.

FIREFOX HAND HELD SIGNAL LAUNCHERS

Now by popular demand we have added our precision machined hand held “Cyclone Systems” signal device launchers from our field tested prototypes. Available in a range of barrel sizes from 17mm to 37/38mm, these launchers will send a variety of effects high into the air or at an angle away from you. Effects include high intensity color signal flares, smoke pellets or canisters, wildlife control cartridges or colorful air burst aerial shells.

Great for launching smoke in Paint Ball Field Games and similar training. “CYCLONE SYSTEMS” 17H SIGNAL BATON/LAUNCHER

Machined from solid 6061 aluminum, the launcher is operated by a #209 shotshell primer to launch flare or smoke pellets and 15 & 17mm wildlife control cartridges (listed elsewhere in catalog) high into the air for signaling. Make your own signal pellets or wildlife control devices! The barrel will accept devices up to .675” OD and our 1/2” ID X 1 1/2” L tubes (Stock# T112) works great for small canister devices. To load simply thread barrel from handle, place a # 209 shotshell primer and thread barrel back on. Insert device into barrel, pull spring loaded knob in handle (firing pin) and release to fire. 8.75” overall length with safety release pin to prevent accidental discharge. Use with shotshell primers alone for very loud audible effects. Comes with instructions. See top diagram B - opposite page. (Lower diagram is 37/38 mm for comparison).

*** NEW ITEMS SOON *** WATCH FOR THEM!!COMPOSITE ROCKET MOTOR SYSTEMS CHROMIUM-MOLYBDENUM STEEL RELOADABLE ROCKET MOTOR SYSTEMS - FRMS COMPLETE, READY TO USE!! MAKE AND CAST YOUR OWN PROPELLANTS REDUCE LAUNCH COSTS GAIN INVALUABLE EXPERIENCE REWARDING HOBBYRELOADABLE BLACK POWDER ROCKET MOTOR SYSTEMS COMPLETEALUMINUM TOOLING SET WITH RELOADABLE ALUMINUM ROCKET MOTOR AFFORDABLE - FUN - REWARDING GREAT TEACHING AID FOR SCHOOLS & COLLEGES TACTICAL HAND HELD SMOKE GRENADE LAUNCHERS WITH RELOADABLE INSERT CANISTER PROJECTILESHAND HELD SIGNAL BATON LAUNCH FLARES, WHISTLES AND AERIAL REPORTS HIGH INTO THE AIR

(17mm, 24mm, 26mm, 28mm, 34mm, 37/38mm)

12 GAUGE COMPONENTS FOR DO-IT-YOURSELF 12 GAUGE HULLS - NEW PRIMED 2 3/4"- RELOADABLE

Brand new primed - ready to load 2 3/4" 12 gauge shot shell hulls for hunting loads or special effects applications such as signal flares, pest control bangs & whistles, etc.

Currently out of stock

12 GAUGE ROLL CRIMPING TOOL

Used for gently rolling the plastic hull inward over the contents for professional looking results. Absolutely mandatory when loading magnum shot shells, tracers, slug loads, etc.. A roll crimp takes up less of the hull than the standard star crimp and promotes longer case life and better seals. Comes with instructions. Fits in standard drill press, friction heats the hull and rolls it inward to the overshot card. Takes only seconds.

GAUGE MAGNUM SHOTCUPS - HIGH DENSITY PLASTIC SPECIAL EFFECTS COLUMNS

Designed for high power 2 3/4" magnum hunting loads, these shot cups hold 1 1/4oz of steel shot or 1 5/8oz of lead. They are also used to contain the composition for special effects loads such as signal flares and flame thrower/incendiary type loads.

- Currently out of stock

12 GAUGE 3/4" DIAMETER OVERSHOT CARDS

Cardboard disk placed over the loaded shotcup or other components in the hull to top it off. They are used to supply a base to roll the hull over onto for the crimp thus sealing the shell.

12 GAUGE INSERT PROJECTILE CASINGS - COLOR CODED FIRE RETARDANT PAPER

Load your own colored signal flares , smoke tracers or wildlife control whistles and bangs! Our insert casings are color coded spiral wound of tough, specially treated fire retardant Kraft paper to help reduce the dangers of spot fires in use. They are designed to fit the 12 gauge hulls without gas seals. Simply compress casing with flare or smoke comp approx 70% full or with audible whistle or bang composition for pest control use. When used in combination with transparent hulls such as the ones we carry, the color coded casings tell at a glance what is loaded. In addition, the casings protect the composition within from fracture (such as flares) from the crimp when fired producing higher altitudes. Uses standard 5/8� plugs to close. Packaged in colors per 100 pcs. Use roll crimping tool to close the hull after loading.

Not yet available.

12 GAUGE "SCREAMERS" - WHISTLE CASING INSERTS

Heavy walled fire resistant casings for making your own 12 gauge whistles - wildlife control cartridges. Simply plug one end and compress 50% full with a standard 70/30 Potassium Perchlorate/Sodium or Potassium Benzoate whistle mixture. Can also be used for bird "bangs". Use 12 gauge roll crimping tool to close hull over insert.

Firefox Enterprises LLC 11612 N. Nelson Lane Pocatello, ID. 83202 firefox-fx@hotmail.com Order & Information Lines: 1 (208) 251-7415          1 (208) 909-8173