EXOTIC       

       HARDWARE  

COMPONENTS

SURVIVAL, PARAMILITARY & SPECIALTY

LIVE REPLACEMENT TRAINING FUSE
FOR POLICE FLASHBANG & SMOKE GRENADES

BUY M201 LIVE DELAY FUZE INSERT, DELAY FUZE SUBASSEMBLY, M213 DELAY FUZE SUBASSEMBLY, 40MM 33/44 HI-LO BRASS CARTRIDGE

These are the actual delay columns, fuze assemblies and 40mm 33/44 Hi-Lo Brass Propellant Cartridges manufactured for the military. They are not out of spec devices, but instead, overruns from gvt. contracts. These are extremely rare to find and usually very expensive. Now you can reload your once fired devices instead of buying new. One source for flash bang grenades gets over $150.00 each for live and another source gets $45.00 each for the innert once fired cores and the fuze subassemblies sell for $25.00 each!!

M201 DELAY FUZE COLUMN - 1.4S Hazmat Shipping Required

These are new M201 delay fuze columns without the threaded fuze subassembly. The once fired delay is pressed out and the new one pressed in, being careful not to press against or damage the primer thus causing accidental firing. Tooling can be made from a wooden dowell with a concave end so it only contacts the rim of the fuze column and not the primer. These fit the M201 subassemblies only. Out of stock

M201 DELAY FUZE SUBASSEMBLY & FUZE COLUMN - 1.4S Hazmat Shipping Required

As the photos above depict, this subassembly consists of the delay fuze column pressed within the threaded subassembly, ready for use. Use the spoon and spring kit from your once fired device to complete the assembly for use. Purchase more M201 delay fuze columns for these above. Out of stock

M213 DELAY FUZE SUBASSEMBLY & FUZE COLUMN - 1.4S Hazmat Shipping Required

As the photos above depict, this subassembly consists of the delay fuze column pressed within the threaded subassembly, ready for use. Use the spoon and spring kit from your once fired device to complete the assembly for use. Out of stock

40mm 33/44 HI-LO BRASS PROPELLANT CARTRIDGES - 1.4S Hazmat Shipping Required

These are the loaded brass propellant cartridges used to fire the 40mm smoke grenades and other devices. They are pressed into place within the 40mm aluminum or steel casings and supply the power to propel the insert. Out of stock

TRACER BULLET LOADING DIES
COMPRESS PYROTECHNICS INTO BULLET BASE

MAKE YOUR OWN COLORFUL TRACERS FOR RIFLE OR PISTOL CALIBERS! Our patent pending tool design features a precision machined threaded (7/8 -14) steel compression die with interchangeable non-sparking brass ram and an aluminum bullet die with interchangeable plastic sleeve housing the pre-drilled bullet for compressing the pyrotechnic tracer composition. Simply thread the compression die into any standard single station ammo reloading press, slip the bullet die into ram press, insert appropriate pre-drilled bullet into sleeve, fill with your favorite composition and compress by lowering press handle - simple!! We have designed the set to use inexpensive interchangeable parts to upgrade to a different caliber without purchasing an additional threaded die set!! Example: if you wish to load both 30 caliber and 45, simply order the die set in one caliber and the upgrade kit for the other. Loading dies include threaded die with lock rings, brass ram, bullet die, bullet sleeve for one caliber and complete instructions listing how to easily drill the bullet base cavities for each caliber using FMJ or hard cast bullets and ordinary drill bits obtained at most any hardware store. Upgrade kits include bullet sleeve and brass ram. See diagram A - opposite page. Call For Availability.
Tracer ammunition start fires!! They are illegal in all state and federal lands and even some shooting ranges. Never use in areas of dry grasses or brush. Choose and inspect your range carefully.

"SILENCER" LOOK BARREL - 17MM - METRIC THREAD FOR BLANK / WILDLIFE CONTROL PISTOLS

Machined from 3 1/2" long solid aluminum and metric threaded to fit the older style 15mm blank pistols with thread-on barrels. Both 15mm & 17mm devices may be used and launched higher becaise of the longer barrel. Its "silencer look" adds character to you pistol as well! Load your own wildlife control cartridges, whistles, bangs, etc. using 9/16" ID X 1/16" wall tubes (roll your own) or flare pellets using our 9/16" pellet pumps for signalling applications.

ADAP17

17mm 3.50" Metric Threaded Aluminum Barrel

$29.70   (4 oz)

9/16 " STAR & FLARE PELLET PUMPS - ALUMINUM

Machined aluminum pump for pressing aerial flares, stars and other compositions such as smoke and ignition pellets that can be fired from 15mm blank / wildlife control pistols. Set includes mold sleeve, ram and instructions with color flare formulations. Now you can use your blank pistol for an aerial signaling. The pellets may be used in aerial shells as well.

ALSP916

9/16" Pellet Pump (true diameter slightly less)

$28.20    (8 oz)

.
 FIREFOX “CYCLONE SYSTEMS”
HAND HELD SIGNAL LAUNCHERS

Now by popular demand we have added our precision machined hand held “Cyclone Systems” signal device launchers from our field tested prototypes. Available in a range of barrel sizes from 17mm to 37/38mm, these launchers will send a variety of effects high into the air or at an angle away from you. Effects include high intensity color signal flares, smoke pellets or canisters, wildlife control cartridges or colorful air burst aerial shells. Great for launching smoke in Paint Ball Field Games and similar training.

“CYCLONE SYSTEMS” 17H SIGNAL BATON/LAUNCHER

Machined from solid 6061 aluminum, the launcher is operated by a #209 shotshell primer to launch flare or smoke pellets and 15 & 17mm wildlife control cartridges (listed elsewhere in catalog) high into the air for signaling. Make your own signal pellets or wildlife control devices! The barrel will accept devices up to .675” OD and our 1/2” ID X 1 1/2” L tubes (Stock# T112) works great for small canister devices. To load simply thread barrel from handle, place a # 209 shotshell primer and thread barrel back on. Insert device into barrel, pull spring loaded knob in handle (firing pin) and release to fire. 8.75” overall length with safety release pin to prevent accidental discharge. Use with shotshell primers alone for very loud audible effects. Comes with instructions. See top diagram B - opposite page. (Lower diagram is 37/38 mm for comparison).

*** NEW ITEMS SOON *** WATCH FOR THEM!!  COMPOSITE ROCKET MOTOR SYSTEMS CHROMIUM-MOLYBDENUM STEEL RELOADABLE ROCKET MOTOR SYSTEMS - FRMS COMPLETE, READY TO USE!! MAKE AND CAST YOUR OWN PROPELLANTS REDUCE LAUNCH COSTS GAIN INVALUABLE EXPERIENCE REWARDING HOBBY   RELOADABLE BLACK POWDER ROCKET MOTOR SYSTEMS COMPLETE ALUMINUM TOOLING SET WITH RELOADABLE ALUMINUM ROCKET MOTOR AFFORDABLE - FUN - REWARDING GREAT TEACHING AID FOR SCHOOLS & COLLEGES   TACTICAL HAND HELD SMOKE GRENADE LAUNCHERS WITH RELOADABLE INSERT CANISTER PROJECTILES  

HAND HELD SIGNAL BATON - LAUNCH FLARES, WHISTLES AND AERIAL REPORTS HIGH INTO THE AIR

(17mm, 24mm, 26mm, 28mm, 34mm, 37/38mm)

 

12 GAUGE COMPONENTS FOR DO-IT-YOURSELF