3/4" ID Solid - 1" dia solid x .100" thick To close various firework tube devices; 12 gauge overshot cards, etc..

3/4" ID x 3/32" center hole - Fits 3/4" ID/24mm also used as a bulkhead with ejection charge flash hole in 24mm phenolic rocket motor cases

1" dia x 3/32" center hole x .100" thick - To close various firework tube devices

1" dia x 3/32" center hole x .100" thick - Fits 1" ID/29mm also used as a bulkhead with ejection charge flash hole in 24mm phenolic rocket motor cases

1 1/4" dia solid x .100" thick - 37/38mm & M212 disc

1 1/4" dia x 3/32" center hole x .100" thick - 1 1/4" fits 38mm phenolic rocket motor cases

1 1/4" dia x 3/8" center hole x .100" thick - 37/38mm & M212 time fuse disc

1 1/4" dia x 3/8" center hole x .100" thick - 1 1/2" fits 54mm phenolic rocket motor cases as well

1 1/2" dia solid x .100" thick - as 6 lb black powder rocket bulkhead and delay well assembly

1 1/2" dia x 3/8" x .100" thick - 1 1/2" fits 54mm phenolic rocket motor cases as well as 6 lb black powder rocket bulkhead and delay well assembly

1 3/4" dia solid x .100" thick - 1 3/4" fits MT134 mortar tube, smoke cans, etc.. 1 1/2" also fits T112UCR tubes for smoke cans, etc., as well as 6 lb black powder rocket bulkhead and delay well assembly

1 3/4" dia x 1/4" center hole x .100" thick - 1 3/4" fits MT134 mortar tube, smoke cans, etc..1 1/2" also fits T112UCR tubes for smoke cans, etc., as well as 6 lb black powder rocket bulkhead and delay well assembly

1 7/8" dia x 3/8" center hole x .100" thick -

1 7/8" dia x 7/16" center hole x .100" thick -

1 7/8" dia x 9/16" center hole x .100" thick -

1 7/8" dia x 5/8" center hole x .100" thick -

2" dia solid x .100" thick - 2" dia fits inside Firefox Tactical Smoke Cans

2" dia x 3/8" center hole x .100" thick - 2" dia fits inside Firefox Tactical Smoke Cans

2" dia x 7/16" center hole x .100" thick - 2" dia fits inside Firefox Tactical Smoke Cans

2" dia x 1/2" center hole x .100" thick - 2" dia fits inside Firefox Tactical Smoke Cans

2" dia x 9/16" center hole x .100" thick - 2" supplied with Firefox Tactical Smoke Kits

2 1/4" dia solid x .100" thick - Fits 2" ID x 1/4" wall Tactical Smoke Cans

2 1/2" dia solid x .100" thick - 3" aerial shell solid end disc

2 1/2" dia x 1/4" center hole x .100" thick - 3" aerial shell, 1/4" time fuse hole disc

3 1/2" dia solid x .125" thick - 4" aerial shell solid end disc

3 1/2" dia x 1/4" center hole x .125" thick - 4" aerial shell, 1/4" time fuse hole disc

4 1/2" dia solid x .125" thick - 5" aerial shell solid end disc

4 1/2" dia x 1/4" center hole x .125" thick - 5" aerial shell, 1/4" time fuse hole disc

5 5/8" dia solid x .125" thick - 6" aerial shell solid end disc

5 5/8" dia x 1/4" center hole x .125" thick - 6" aerial shell, 1/4" time fuse hole disc

KRAFT AERIAL CANISTER SHELLS - SALUTE, STAR & MULTI-BREAK - High strength spiral wound Kraft casings with clearance for string tying (optional) and reinforced paper pasting. Order end discs (below) for appropriate ID's & OD's for shell finishing. Shells can be stacked and pasted for various two or three break effects. NOTE: For discs and endcaps to fit the cans below, go HERE

3" Salute shell - heavy wall - 2 1/8" ID X 2 1/2" OD X 3" long

3" Star shell, single or multi break - 2 3/8" ID X 2 1/2" OD X 2 3/4" long

4" Salute shell - heavy wall - 3.0" ID X 3 1/2" OD X 4" long

4" Star shell single or multi break - 3 3/8" ID X 3 1/2" OD X 3 1/2" long

4" Star shell - 3 3/8" ID X 3 1/2" OD X 4" long

5" Salute shell - heavy wall - 4.0" ID X 4 1/2" OD X 4 1/2" long

5" Star shell - multi break - 4 3/8" ID X 4 1/2" OD X 4 1/2" long

6" Star shell or multi break - 5 1/2" ID X 5 5/8" OD X 5 1/2" long

AERIAL SHELL PAPER CAPS -

1 3/4" Paper Caps fit 1 3/4 " OD Tubes & Cans - (also fits discarded standard bathroom tissue & paper towell tubes. Free tubes to make smoke cans, 2" mines, exploding targets & cannister aerial shells) Simply plug bottom of tube with a disc cut from a cerael box or similar, using the tube as a pattern and cutting disk inside the drawn line. A drawing compass is a great way to draw perfectly round discs. Use a length of PVC pipe (or similar) that fits the inside of the tube to push the discs in. Apply glue (PVOH) inside and out, allow to dry and glue another disk in the bottom. Use plenty of glue. If making aerial shells or mines, punch a 1/4" hole in several discs glued together and glue the time fuse in place. Push it in place from the top to the bottom of tube using the PVC pipe. Glue in place and allow to dry. Add enough glue inside around fuse 3/8" thick and allow to dry upright (with fuse in a hole on the workbench). This step will reinforce the bottom to withstand the lift charge shock. Note; Before filling with composition, brush the inside of tube (with bottom discs glued in place) with Firefox Fire Retardant to discourage burning fallout or smoke can burnthrough. Discs can also be treated. Moisten with wheat paste and wrap 6 1/2" wide strip of kraft paper bag around tube (parallel). This leaves enough overlap to paste over end discs to close. Do so over the bottom disc, with or without time fuse, depending on application and glue the end cap on. Fill the tube with appropriate composition(s) or garnitures and close in the same manner. Apply more paste to outside and wrap on more kraft paper folding over the ends as before. The number of paper laps is just enough to effect a proper fit in the mortar tube. It should have 1/8" clearance on each side (1/4" total) for proper fit in mortar. They are fired from a 2" ID mortar. Smoke cans; Fuse can be added to the top end for smoke devices. Press moist smoke comp in place leaving a tapered core in the center to increase surface area of burn / smoke volume. Place a ring of glue around inside of tube and push a double disc punched with a 1/2" center hole in place leaving approx 1" of empty space from composition. Glue and dry. Fold paper strips over the edge and inside tube against discs to reinforce against pressure. Secure fuse in place with prime slurry and place an end cap over to finish. This cap is not glued in place and removed for use.

2 1/2" Paper Caps fit 2 1/2" OD Tubes & Cans - (fits 3" paper aerial star & salute cans)

3 1/2" Paper Caps fit 3 1/2" OD Tubes & Cans - (fits 4" star & salute cans)

PARALLEL WOUND (CONVOLUTE) GENERIC TUBES - NATURAL KRAFT BROWN - Parallel wound tubes strong enough to sound like wood when struck together. These tubes are many times stronger than spiral wound @ the same thickness. Low cost natural brown kraft color. Wall thickness and subsequent OD's are nominal unless otherwise noted. No ATFE required to order paper plugs, paper caps, paper discs, paper cup sets or tubes longer than 10"

3/8" ID X 3 1/2" LONG X 3/32" WALL - Spollettes, falls, whistles, 2 oz rocket, shell inserts, ground chasers, etc..

3/8" ID X 24" LONG X 3/32" WALL - Cut to desired length for: Spollettes, falls, whistles, 2 oz rocket, shell inserts, hummers, ground chasers, etc.. Cut to desired length. No ATFE required to order this length tube

7/16" ID X 24" LONG X 3/16" WALL - Cut to desired length for: Lasger Shell Spollettes, falls, whistles, shell inserts, ground chasers, hummers, etc.. Cut to desired length. No ATFE required to order this length tube

1/2" ID X 5" LONG X 1/8" WALL - Candles, 4 oz rocket, candle, buzz bomb, whistles, fountains, gerbs, hummers, shell inserts, etc..

1/2" ID X 24" LONG X 1/8" WALL - Cut to desired length for: Candles, 4 oz rocket, candle, buzz bomb, whistles, gerbs, fountains, shell inserts, hummers, etc.. Cut to length. No ATFE required to order this length tube

5/8" ID X 3 1/2" LONG X ~.105" WALL - 2 stage whistle rocket, hummer, gerbs, spinners, #00 mortar, shell inserts, etc.. Fits nose cones and fin sets RNCS & RFS for use with whistle rocket tool set #TSWROC

5/8" ID X 5 1/2" LONG X ~.105" WALL - 8 oz rocket, candle, hummer, gerbs, whistle & strobe rockets, fountains, spinners, #00 mortar, shell inserts, tourbillion, etc.. Cut to length.

5/8" ID X 24" LONG 9/64" WALL - Cut to desired length for: 8 oz rocket, candle, hummer, gerbs, whistle & strobe rockets, fountains, spinners, #00 mortar, shell inserts, tourbillion, etc.. Cut to length. No ATFE required to order this length tube

3/4" ID X 8" LONG X 9/64" WALL - 1 lb rocket, candle, gerbs, fountains, whistle & strobe rockets, tourbillion, #0 mortar, etc..

3/4" ID X 24" LONG X 9/64" WALL - Cut to desired length for: 1 lb rocket, candle, gerbs, fountains, whistle & strobe rockets, tourbillion, #0 mortar, etc.. Cut to desired length. No ATFE required to order this length tube

7/8" ID X 8" LONG X .1875" WALL X 1 1/4" OD - 32oz rocket, whistle & strobe rockets, candle, gerbs, fountains, tourbillions

7/8" ID X 24" LONG X .191" WALL X 1.260" OD - Cut to desired lengths for: 32oz rocket, whistle & strobe rockets, candle, gerbs, fountains, tourbillions. Cut to desired lengths

1" ID X 10 1/4" LONG X 1/4" WALL - 48oz rocket engine, whistle & strobe rockets, candle, gerbs, fountains, tourbillion, #1 mortar, etc..No ATFE required to order this length tube

1" ID X 24" LONG X 1/4" WALL - 48oz rocket engine, whistle & strobe rockets, candle, gerbs, fountains, tourbillion, #1 mortar, etc.. Cut to desired lengths. No ATFE required to order this length tube

1" ID X 24" LONG X 1/8" WALL - Cut to desired length for: Candles, falls, rains & gerbs, fountains, whistles, tourbillion, #1 mortar, etc.. Cut to desired length. No ATFE required to order this length tube

KRAFT PAPER STOCK 40# WT, 18" WIDE X 1275 FT - Make your own high strength paper tubes and spherical star shells! Save money and enjoy the ultimate satisfaction of making your own tubes and shells from scratch. Our booklet "Making Professional Homemade Paper Tubes From Scrap Materials" (Stock # TRTUBE) will tell you how!